Lighting System Power & Wiring: A Scenario-Based Guide (2025)

There's no single "right" way to power a lighting system

Every week someone asks me whether they should wire their chandelier in series or parallel, or which driver to pick for a Zigbee light setup. My honest answer is that it depends—but not on the things most people expect. It depends on three questions: how many fixtures are on the circuit, whether you need dimming or smart control, and whether the install is residential or commercial. Get those three right and the rest is detail work.

I'm not going to pretend there's a universal answer. In our Q1 2024 audit cycle, I reviewed roughly 280 driver and fixture specifications before they went to project teams. About 15% of first deliveries failed because someone assumed a driver spec was "close enough" when it wasn't. The failures weren't on the products—they were on the assumptions behind them.

Here's how I'd break down the three scenarios that cover most of what we actually see.

Scenario A: One chandelier, one switch, and you want it done right

This is the classic "how to wire a chandelier with multiple lights" question. The good news: it's the easiest scenario, and the wiring logic is less scary than it sounds.

For a chandelier with multiple lamp holders, you almost always want the bulbs wired in parallel—not series. Series wiring (the string-of-Christmas-lights approach) means one failed bulb kills the whole circuit, and the voltage across each bulb drops as you add more. Parallel wiring keeps each bulb at full circuit voltage and lets the others keep working if one fails.

Here's the part most guides skip: the driver has to match the total load, not the number of bulbs. If your chandelier has eight 5W bulbs, that's a 40W continuous load. Size the driver for at least 20% headroom—so a 50W unit minimum. After a few expensive rounds of guesswork I settled on a simple rule: never run a driver above 80% of its rated wattage for continuous use.

Now the brand question. If you're looking at a Toshiba driver for a residential chandelier, you're probably also seeing "Toshiba laptop power supply" results—they surface in the same searches because they share a brand name and nothing else. They are not interchangeable. A laptop power supply delivers regulated DC at a fixed voltage (typically 19V) and is not designed for the constant-current load of an LED string. Use the wrong one and you'll either get flicker or you'll cook the bulbs. Use the specified driver.

One more thing—and this is where I'd push back on the "just buy the cheapest compatible driver" advice you see online. The driver is the first component to fail in most residential chandelier complaints. In 2023 we ran a blind comparison of a $12 no-name driver against a $28 name-brand unit: same wattage, same claimed specs. The no-name units started failing at month fourteen; the name-brand units are still running as of January 2025. On a per-year basis the cheap one cost more.

Scenario B: Commercial multi-zone lighting with dimming

This is where things get real. In commercial jobs, the driver isn't a single part—it's a specification. When we audit a commercial lighting system, we check:

  • Constant-current versus constant-voltage driver—and whether the whole zone uses the same type
  • Dimming protocol compatibility (0-10V, DALI, or trailing-edge) between driver and control
  • Inrush current when multiple drivers switch on at the same time
  • Thermal derating—drivers in a closed ceiling void run hotter than the datasheet assumes

The single biggest mistake I see in commercial jobs is mixing constant-current and constant-voltage drivers in the same zone. They don't dim the same way and the controls won't behave consistently. We had a retail project in Q2 2024 where half the zone flickered at low dim levels because someone used a CV driver to save a line item on the BOM. The fix was a $900 driver swap plus a re-inspection; the original line item saved about $60.

If a supplier hands you a spec sheet that lists a Toshiba driver without a model number, ask for the full part number and the datasheet. Toshiba makes multiple driver lines and they aren't interchangeable across all loads. The same is true for the Toshiba laptop power supply line—same brand, different product, different electrical behavior. Don't let a brand name do the spec work.

Scenario C: Zigbee-controlled smart lighting

Zigbee lights are where the wiring decisions and the control decisions collide. Most people assume the hard part is pairing the bulbs to the hub. It's not. The hard part is making sure the driver and the Zigbee module agree on how the light is supposed to behave at low output.

A few things I'd check before specifying Zigbee lights in a commercial or high-end residential job:

  1. Does the Zigbee module sit on the driver side or the bulb side? This changes the failure modes and the replacement cost.
  2. Are the bulbs Zigbee 3.0 or an older profile? Mesh compatibility is not automatic across generations.
  3. What happens when the gateway goes offline? A good system falls back to local switch control; a cheap one goes dark or freezes on the last state.

Here's something most installers won't tell you: a Zigbee lighting system is only as reliable as its weakest mesh node. In 2022 we specified a 40-node Zigbee commercial retrofit and lost three weeks chasing an intermittent dropout. The cause wasn't the gateway or the drivers—it was one repeater placed behind a metal partition. Moving it two meters fixed the whole system. The lesson stuck: plan the mesh, not just the wiring.

How to figure out which scenario you're in

Ask yourself three questions, in order:

  1. How many fixtures are on the circuit? One or two, and you're probably in Scenario A. A zone with ten or more, Scenario B. Mixed smart and non-smart in the same space, Scenario C.
  2. Do you need dimming, and if so, what protocol? If the answer is "yes but I don't know which," stop and find out before buying anything. This single answer decides which drivers you can use.
  3. Who's going to maintain it? If the answer is "the facilities team for the next ten years," buy the driver with a full datasheet and a serviceable part number. If it's a single chandelier you'll touch twice a decade, a good residential driver is enough.

I'd rather tell you that our own scenario classification doesn't always fit cleanly than pretend it does. A hotel lobby with twenty chandeliers is technically Scenario A wiring, but the maintenance profile makes it Scenario B. That's fine. The classification is a starting point, not a rule.

If you take one thing from this: match the driver to the load, and match the control to the driver. Everything else in a lighting system is downstream of those two decisions.

Clara Whitmore

Clara Whitmore

Clara Whitmore is a lighting photometry and LED source analyst specializing in bulbs, tubes, strips, panels, and integrated luminaires. She interprets IES LM-79 measurements and TM-30 color rendition data through luminous flux, efficacy, intensity distribution, CCT, chromaticity, fidelity, and gamut metrics. She writes evidence-led comparisons for specifiers selecting source formats and luminaires for commercial interiors, industrial spaces, or horticultural systems where measured optical and color performance matter.

← Sylvania Procurement Checklist: 7 Steps to Catch Hidden Costs Before You OrderWhy the Cheapest Bulb on Your Invoice Is Usually the Most Expensive One →